Having a tiny apartment is great during the winter. It's cozy, for one thing. And it's easier (and costs less) to keep warm. But a smaller apartment means floor space is a hot commodity, and a Christmas tree may compete with your dining room table or a nearby couch. Thankfully we've got a great DIY project to solve this dilemma. 

A wooden Christmas tree offers an excellent (and memorably festive) solution for a small space. You can customize the size of the wooden tree to fit your space, it folds flat (which makes it great for storage), and if you happen to have evergreen-induced allergies—this will let you avoid them all together! 

lets make a wood christmas tree

Step 1: Cut wood pieces

Begin by cutting pieces to size with a circular saw or a hand saw and miter box. (Refer to the diagram below as you make the cuts.)

wooden christmas tree plan

Step 2: Pick out a dowel

Before we do anything else, we’re going to compare our dowel diameter to our spade bit. Drill bits are very precise in their measurements, while dowels (like all wood) vary a little in size. This means that sometimes you’ll pick out a dowel that’s too small to secure firmly in the hole, and sometimes you’ll get one that’s too big to fit.

There are two solutions to this problem: You can drill a hole with a ¾” spade bit in a piece of scrap wood, take it to your local Dunn Lumber, and buy a dowel that fits snugly in the hole. Or if you already have a dowel that has a little too much wiggle room, you can break up some toothpicks and wedge them into the hole around the dowel. Combined with wood glue this solution will hold well.

Step 3: Mark center 

Using a combination square, find and mark the center of each piece.

marking wood for tree

Step 4: Drill

Stack all the pieces in pairs, and clamp the pairs to the edge of the work bench or saw horse. With a ¾” spade bit, drill through the pieces using the pencil mark as a guide. Only drill through the top piece of the pair, then switch positions and drill through the new top piece (having a piece on the bottom when you're drilling helps prevent breakage). Set aside one 2 ½” square (as a spacer) and one 7 ¼”  square (as the base piece). 

Do this with all the one-by-three branches, and the remaining 2 ½” and 7 ¼” squares.

marking wood with a pencil

clamping wood down

spade into wood for tree

Step 5: Complete partial drilling

Grab the two pieces you set aside. Drill only halfway through the 2½” and the 7½” square. (Refer to the picture below.)

drill only halfway

hole for wooden christmas tree

Step 6: Sand

Sand all of the pieces, focusing on the cut edges and removing any large breakage around the drill holes (though these will be mostly covered up). If you want a smoother finish, you can grab a sander.

sanding wood

wood for diy xmas tree

Step 7: Cut and glue tree trunk

Cut your dowel to approximately 29 ½” using a chop saw or a hand saw. (This length may need to be adjusted based on minor variants in wood dimensions, and depending on the depth of the holes in the top and bottom.)

Apply wood glue to the end of the dowel and insert it into the bottom 7 ¼” piece (the one you drilled only halfway through).

glue dowel

cut and glue dowel

Step 8: Add branches

Slide on the remaining three 7 ¼” squares. Slide on the longest two branches (30 ½”), then a 2 ½” spacer. Continue this pattern up the dowel from the longest to the shortest branches.

add branches to your christmas tree

adding branched to your xmas tree

Step 9: Shape your tree

We decided to skip the second branch for the top of the tree (the 5 ½”) and replaced it with an extra 2 ½” piece. The original design was for the last two 5 ½” branches and just one 2 ½” square on top—but that's one of the great things about this pattern! It can totally be adjusted according to the look you want.

shape your large wooden tree

Step 10: Glue top

Do a dry fit of the final top piece to make sure the dowel is the correct length, and trim it if necessary. Attach the top with glue and press firmly in place.

glue the top

top of christmas tree

Step 11: Stagger branches

If desired, use a 1 ½” spade bit to create an indent on the end of each branch (or select branches) to hold a votive candle. Use electronic votives to avoid fire hazards.

how to make a wooden christmas tree

wooden christmas tree

Your wooden Christmas tree is ready! The branches can be spread out or lined up for different effects, and the tree can be decorated with ornaments, lights, or paint! 

diy wooden christmas tree

Love Christmas crafts? Find all of our festive 12 Days of DIY projects here.